高面板坝全寿命周期变形控制方法及应用

高面板坝的变形对面板的安全运行有着特别重要的影响，国内外已建的高面板坝工程中，因坝体变形大导致防渗面板挤压破损，坝体渗漏量大的实例较多，不得不降低水库水位进行修复处理，造成较大的经济损失乃至给大坝的长期运行留下安全隐患。通过发生挤压破损的实例分析，发现变形控制缺乏系统性是发生面板挤压破损的主要因素，为预防面板破损，系统提出了“控制坝体总变形，转化有害变形，适应纵向变形”的坝体变形控制方法，并在使用软硬岩混合料筑坝的董箐面板堆石坝中得到的应用，取得了良好效果，该工程运行至今达十余年，未见面板有挤压破损迹象，该方法对建设200 m以上乃至300 m级超高面板坝具有重要借鉴意义。     

Profiling hot isostatically pressed canister–wasteform interaction for Pu-bearing zirconolite-rich wasteforms

Zirconolite-rich full ceramic wasteforms designed to immobilize Pu-bearing wastes were produced via hot isostatic pressing (HIP) using stainless steel (SS) and nickel (Ni) HIP canisters. A detailed profiling of the elemental compositions of the major and minor phases over the canister–wasteform interaction zone was performed using scanning electron microscopy combined with energy-dispersive X-ray spectroscopy (SEM-EDS) characterization. Bulk sample analyses from regions near the center of the HIP canister were also conducted for both samples using X-ray diffraction and SEM-EDS. The sample with the Ni HIP canister showed almost no interaction zone with only minor diffusion of Ni from the inner wall of the canister into the near-surface region of the wasteform. The sample with the SS HIP canister showed ∼100–120 μm of interaction zone dominated by high-temperature Cr diffusion from canister materials to the wasteform with the Cr predominantly incorporated into the durable zirconolite phase. We also examined, for the first time, changes to the HIP canister wall thickness caused by HIPing and demonstrated that no canister wall thinning occurred. Instead, in the areas examined, the canister wall thickness was observed to increase (up to ∼20%) due to the compression occurring during the HIP cycle. Further, only sparse formation of (Cr, Mn)-rich oxide particles were noted within the HIP canister inner wall area immediately adjacent to the ceramic material, with no evidence for reverse diffusion of ceramic materials. Though the HIP canister–wasteform interaction extends to ∼120 μm when using an SS HIP canister for the system investigated, this translates to <<1 vol.% for an industrial scale HIPed wasteform. Importantly, the HIP canister–wasteform interactions did not produce any obviously less durable phases in the wasteform or had any detrimental impact on the HIP canister properties.     

Novel pearl millet couscous process for West African markets using a low-cost single-screw extruder

Traditional West African pearl millet couscous products are popular; however, their preparation is laborious, time-consuming and energy-demanding, involving agglomeration, steaming, drying and sieving steps. In this study, a process was developed to produce millet couscous using a high pressure, high temperature and low-cost single-screw extruder. The innovation was to directly process the cooked low-moisture extrudate to a couscous product by drying and milling to the appropriate particle size (ranging between 1 and 2 mm). Throughput for the traditional process as prepared for commercial sale is 50 kg per day, but with the same amount of labour, the extrusion process yields ~350 kg per day. A consumer sensory study held in Niamey (Niger) showed that the extruded millet couscous was comparable to traditional couscous, though this was dependent on selection of the proper millet variety. This novel extrusion process could stimulate small- to medium-scale manufacturing of couscous and couscous-type products in West Africa.     

Combined effect of channel to rib width ratio and gas diffusion layer deformation on high temperature – Polymer electrolyte membrane fuel cell performance

The present study investigates the combined influence of Channel to Rib Width (CRW) ratio and clamping pressure on the structure and performance of High Temperature-Polymer Electrolyte Membrane Fuel Cell (HT-PEMFC) using a three-dimensional numerical model developed previously. It also considers the impact of interfacial contact resistance between the Gas Diffusion Layer (GDL) and Bipolar Plate (BPP). The structural analysis of the single straight channel HT-PEMFC geometry shows that the von-Mises stress greatly increases in the GDL under the ribs as the CRW ratio increases resulting in considerably high deformation. The cell performance analysis depicts the significance of ohmic resistance and concentration polarization for different CRW ratios, particularly at higher operating current densities. However, in low to medium current density regions, the CRW ratio has little influence on cell performance. A substantial impact on the species, overpotential, and current distributions is observed. The findings also reveal that the CRW ratio significantly affects the temperature distribution in the cell.     

有砟轨道路基翻浆冒泥模型试验系统的研发与应用

为研究既有线有砟轨道路基的翻浆冒泥机理，自主研发了一套能够模拟循环荷载–湿化耦合作用的模型试验系统。模型试样直径500 mm，由厚度分别为350 mm的路基土和200 mm的道砟组成，整个试样在高强度透明有机玻璃模型筒中制备完成。模型试验系统配备有监测荷载、位移、体积含水率和孔隙水压力的4种传感器，并通过高清相机对颗粒迁移过程进行图像捕捉。基于所研发的试验系统，针对辛泰铁路典型翻浆冒泥病害路段土样，开展翻浆冒泥模型试验。试验结果表明：动孔隙水压力是导致翻浆冒泥病害产生的关键因素。随着体积含水率的增加，动孔隙水压力引起的颗粒迁移量逐渐增加；在饱和状态下，会引起大量颗粒迁移，翻浆冒泥现象显著。试验结束时，道砟污染指数达到25%，在实际工程中已严重影响铁路的正常运营，有必要对污染道砟进行换填。     

一种用于电气设备状态监测的新式FBG传感器北大核心CSCD

为了监测绕组变压器的静态应力场和发生短路等故障时的动态应力变化,设计了一种用于电气设备状态监测的新式FBG传感器。该传感器由聚醚醚酮材料封装的FBG构成,通过内部圆锥形空腔结构实现将轴向应力集中于FBG敏感位置。通过仿真对不同压力强度下传感器结构的应力场部分及形变趋势进行了计算与分析,论证了设计的合理性。实验分别对静态载荷和动态冲击进行测试,结果显示,在静态压载测试中,当100 N相似文献   

基于数值模拟的挤压参数对AZ91镁合金管转角焊合室分流挤压焊合压力的影响规律研究

提出了一种镁合金管材转角焊合室分流挤压新工艺，该工艺可在有效延长焊合室长度和焊合时间前提下保证舌针刚度，从而保证管材尺寸精度，并且可通过转角剪切变形机制增加预焊合金属变形量和动态再结晶程度，从而有利于提高管材性能和焊缝焊合性能。利用有限元法揭示了转角焊合室分流挤压成形过程中金属的流动特征，应变分布特征和焊合室内的静水压力分布特征。结果表明，整个挤压过程无金属折叠，从而保证管材的表面质量；流经转角后预焊合金属变形量明显增加，有利于提高管材质量和焊缝质量。最后，研究揭示了坯料初始温度，挤压速度和模具转角对焊合室内静水压力的影响规律。结果表明，随着挤压速度的增加和模具转角的增大，转角焊合室内静水压力增大；随着坯料预热温度的增加，转角焊合室内静水压力呈先增大后减小的趋势。     

Influence of pressure and dwell time on pressure-assisted sintering of calcium cobaltite

Calcium cobaltite Ca₃Co₄O₉, abbreviated Co349, is a promising thermoelectric material for high-temperature applications in air. Its anisotropic properties can be assigned to polycrystalline parts by texturing. Tape casting and pressure-assisted sintering (PAS) are a possible future way for a cost-effective mass-production of thermoelectric generators. This study examines the influence of pressure and dwell time during PAS at 900°C of tape-cast Co349 on texture and thermoelectric properties. Tape casting aligns lentoid Co349. PAS results in a textured Co349 microstructure with the thermoelectrically favorable ab-direction perpendicular to the pressing direction. By pressure variation during sintering, the microstructure of Co349 can be tailored either toward a maximum figure of merit as required for energy harvesting or toward a maximum power factor as required for energy harvesting. Moderate pressure of 2.5 MPa results in 25% porosity and a textured microstructure with a figure of merit of 0.13 at 700°C, two times higher than the dry-pressed, pressureless-sintered reference. A pressure of 7.5 MPa leads to 94% density and a high power factor of 326 µW/mK² at 800°C, which is 11 times higher than the dry-pressed reference (30 MPa) from the same powder.     

Revealing the relationships between alloy structure,composition and plastic deformation in a ternary alloy system by a combinatorial approach

A high-throughput approach based on magnetron co-sputtering of alloy libraries is employed to inves-tigate mechanical properties of crystalline and amorphous alloys in a ternary palladium(Pd)-tungsten(W)-silicon(Si)system with the aim to reveal the difference in plastic deformation response and extract the relevant structure-property relationships of the alloys in the system.It was found that in contrast to crystalline alloys,the amorphous ones,i.e.,metallic glasses,exhibited a much smaller fluctuation range in the plasticity parameters(Er2/H and Wp/Wt),indicating a significant difference in the plastic deformation mechanism controlling the mechanical properties for the respective alloys.We propose that the inho-mogeneous deformation of amorphous alloys localized in thin shear bands is responsible for the weaker compositional dependence of both plasticity parameters,while dislocation gliding in crystalline materials is significantly more dependent on the exact structure,thus resulting in a larger scattering range.Based on the representative efficient cluster packing model,a set of composition-dependent atomic structural models is proposed to figure out the structure-property relationships of amorphous alloys in Pd-W-Si alloy system.     

Molding,patterning and driving liquids with light

When a laser beam induces surface tension gradient at the free surface of a liquid, a weak surface depression is expected and has been observed. Here we report giant depression and rupture in “optothermocapillary fluids” under the illumination of laser and sunlight. Computational fluid dynamics models were developed to understand the surface deformation and provided desirable physical parameters of the fluid for maximum deformation. New optothermocapillary fluids were created by mixing transparent lamp oil with different candle dyes. They can be cut open by sunlight and be patterned to different shapes and sizes using an ordinary laser show projector or a common laser pointer. Laser driving and elevation of optothermocapillary fluids, in addition to the manipulation of different droplets on their surface, were demonstrated as an efficient controlling method and platform for optofluidic operations. The fundamental understanding of light-induced giant depression and creation of new optothermocapillary fluids encourage the fundamental research and applications of optofluidics.